Prodigital Technology Corp.
12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C.
This time we introduce the performance of fully-filled LED soft strip lights.
The original LED step lights used sleeved LED soft strip lights and LED glue strip lights.
These two models are known in the industry as having an IP65 rating, but this approach is not recommended for use in outdoor engineering cases or LED landscape cases.
Difference description:
A.LED sleeve soft strip lights are actually composed of bare board + silicone sleeve, achieving dustproof and waterproof.
1. When the LED is hit by a frontal impact, the silicone sleeve is soft and does not protect the internal LED.
2. The inlet end of the casing must be properly protected to avoid water intrusion due to pulling and rupture after construction.
3. When the waterproofing of the on-site wiring is poor, water or moisture will penetrate the copper wire's cooling and heating effects, causing siphonage and water intrusion.
B. LED glue strip lights are covered with a layer of PU glue on the exposed LED board to achieve dustproof and waterproof on the front.
1. The main disadvantage of the LED flexible strip light is that the back is not waterproof
Outdoor lighting mainly depends on the quality of the product itself + the quality of on-site construction to extend its service life.
Factory customization
Recommended length: DC24V length 20 meters double-ended power supply, DC12V length 10 meters double-ended power supply
Color temperature range: 2700K ~ 6500K
Power range: 5W ~15W/meter, single row
Waterproof level: IP68
Outlet method: 2 wire length < 10 meters
Leave a waterproof layer on the front and back of the PCBA LED soft board, and tightly cover the LED and soft board.
The wires are also wrapped in adhesive material, and the outer layer has a heat-shrinkable sleeve to enhance waterproofing and reduce the pulling force that may cause the adhesive material to break.
After learning about the product, go to the construction site to see actual performance.
Removing glue from lamp power wiring hole cover
Clear the original LED glue strip lights and LED tube soft strip lights operations,
Site bonding requires silicone to reinforce waterproofing
Use a scraper to remove it and it will almost become crispy!
Removing old silicone takes a lot of time!!
Take out the arrangement position of LED soft strip lights
Peel off the 3M adhesive on the back and press along the edges to fix it!
After pressing, apply glue to the power hole.
The 3M adhesive tape is only for temporary fixation. In actuality, the upper and lower edges of the LED flexible strip lights and the joints with the wall must be firmly covered with a layer of glue to prevent them from falling off.
Fixed completed appearance
Actual effect at night
LED soft strip light products https://www.prodigital.com.tw/en/product_cg257608.html
Introduction to various types of LED soft strip lights https://www.prodigital.com.tw/en/hot_362663.html
https://www.prodigital.com.tw/en/hot_471661.html
Taiwan Hsinchu Community Landscape LED Step Light LED Outdoor Full Glue-filled Soft Strip Light Construction Case
2024-06-27
2025-06-27
Prodigital Technology Corp.
12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C.
https://www.prodigital.com.tw/en/hot_471661.html
Prodigital Technology Corp.
12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C.
https://www.prodigital.com.tw/en/hot_471661.html
https://schema.org/EventMovedOnline
https://schema.org/OfflineEventAttendanceMode
2024-06-27
http://schema.org/InStock
TWD
0
https://www.prodigital.com.tw/en/hot_471661.html
Browsing site by scanning QR Code
