LED High Bay Light install case

Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C.

This time we introduce the performance of fully-filled LED soft strip lights. The original LED step lights used sleeved LED soft strip lights and LED glue strip lights. These two models are known in the industry as having an IP65 rating, but this approach is not recommended for use in outdoor engineering cases or LED landscape cases. Difference description: A.LED sleeve soft strip lights are actually composed of bare board + silicone sleeve, achieving dustproof and waterproof. 1. When the LED is hit by a frontal impact, the silicone sleeve is soft and does not protect the internal LED. 2. The inlet end of the casing must be properly protected to avoid water intrusion due to pulling and rupture after construction. 3. When the waterproofing of the on-site wiring is poor, water or moisture will penetrate the copper wire's cooling and heating effects, causing siphonage and water intrusion. B. LED glue strip lights are covered with a layer of PU glue on the exposed LED board to achieve dustproof and waterproof on the front. 1. The main disadvantage of the LED flexible strip light is that the back is not waterproof Outdoor lighting mainly depends on the quality of the product itself + the quality of on-site construction to extend its service life. Factory customization Recommended length: DC24V length 20 meters double-ended power supply, DC12V length 10 meters double-ended power supply Color temperature range: 2700K ~ 6500K Power range: 5W ~15W/meter, single row Waterproof level: IP68 Outlet method: 2 wire length < 10 meters Leave a waterproof layer on the front and back of the PCBA LED soft board, and tightly cover the LED and soft board. The wires are also wrapped in adhesive material, and the outer layer has a heat-shrinkable sleeve to enhance waterproofing and reduce the pulling force that may cause the adhesive material to break. After learning about the product, go to the construction site to see actual performance. Removing glue from lamp power wiring hole cover Clear the original LED glue strip lights and LED tube soft strip lights operations, Site bonding requires silicone to reinforce waterproofing Use a scraper to remove it and it will almost become crispy! Removing old silicone takes a lot of time!! Take out the arrangement position of LED soft strip lights Peel off the 3M adhesive on the back and press along the edges to fix it! After pressing, apply glue to the power hole. The 3M adhesive tape is only for temporary fixation. In actuality, the upper and lower edges of the LED flexible strip lights and the joints with the wall must be firmly covered with a layer of glue to prevent them from falling off. Fixed completed appearance Actual effect at night LED soft strip light products https://www.prodigital.com.tw/en/product_cg257608.html Introduction to various types of LED soft strip lights https://www.prodigital.com.tw/en/hot_362663.html https://www.prodigital.com.tw/en/hot_471661.html Taiwan Hsinchu Community Landscape LED Step Light LED Outdoor Full Glue-filled Soft Strip Light Construction Case 2024-06-27 2025-06-27

Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C. https://www.prodigital.com.tw/en/hot_471661.html

Prodigital Technology Corp. 12F, No.358 Chung Hwa road, Chu pei city, Hsin chu county, Taiwan R.O.C. https://www.prodigital.com.tw/en/hot_471661.html

https://schema.org/EventMovedOnline https://schema.org/OfflineEventAttendanceMode

2024-06-27 http://schema.org/InStock TWD 0 https://www.prodigital.com.tw/en/hot_471661.html

Prodigital Technology Corp.

Home Hot News Application articles / Other Taiwan 400W for 120W high patio lights / 3 times lower power consumption / 3 times brightness enhancement / three years warranty / heavy oil area lamps / 130lm/W / 15,600lm

This time introduces the replacement of LED 120W high ceiling light in Xinzhuang District Iron and Steel Factory (Taiwan)

LED High Bay Light 240W install

The space is 15x45x9 meters, the number of installed lamps is 14盏, and the customer responds with 400W mercury lamps.
Since the installation is used, the light source is easy to be broken (the stabilizer has been installed), and the mercury lamp has been switched on for a long time.
Light fading illumination is no longer acceptable.

LED Illumination Simulation

LED Illumination Simulation

The illuminance value of the installed luminaire is confirmed by simulation. The estimated illuminance of this steel heavy oil zone will be greater than 300 Lux.

LED High bay light Illuminance Measurement

LED High bay light Illuminance Measurement

Actual measured value before installation

LED High bay light Illuminance Measurement

Panoramic shooting comparison

LED High Bay Light Installation Photos

The LED itself already has a good power supply.
This regulator must be dismantled for the LED to create additional power losses.

LED High Bay Light Installation Photos

Replacing the LED luminaire, the E40 connector is directly installed.
And install a fall arrester to prevent the crane from moving for a long time and causing it to fall.
Note: The same is true for locks or hangs. This is a very important part!!

LED High Bay Light 120W install

LED High Bay Light 120W install

Installed photo

LED High Bay Light 120W install

This photo is compared with the pre-installation, the floor is not dim.

LED High bay light Illuminance Measurement

According to the measurement, there are 200lux in the corner area to meet the customer's needs.

Mercury Lamp 400W

Mercury bulb close-up removed.
The above photos are forbidden to be reproduced in any form!

Previous Back to List Next